[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: 19991027: Solaris 7

Martin,

> To: address@hidden
> From: address@hidden (Martin Ridal)
> Subject: Solaris 7
> Organization: .
> Keywords: 199910251557.JAA00350

In the above message, you wrote:

> I am trying to build the netcdf3.4 on a 64 bit solaris 7 by adding
> the flags -xtarget=native -xarch=v9
> Somehow it does not work.
> Hope you can help.
> 
> 
>       Martin Ridal
> 
> 
> 
> Here is the requierd information:
> 
> uname -a: SunOS odin3 5.7 Generic_106541-02 sun4u sparc SUNW,Ultra-4
> 
> VERSION contains: 3.4
> 
> This is how I modified the macros.make file:
> 
> # Preprocessing:
> M4            = m4
> M4FLAGS               = -B10000
> CPP           = cc -E
> CPPFLAGS      = $(INCLUDES) $(DEFINES) -DNDEBUG
> FPP           = fpp
> FPPFLAGS      = -D__SUNPRO_F90
> CXXCPPFLAGS   = $(INCLUDES) $(DEFINES)
> 
> 
> # Compilation:
> CC            = /opt/SUNWspro/bin/cc
> CXX           = 
> FC            = /opt/SUNWspro/bin/f90
> CFLAGS                = -O -xtarget=native -xarch=v9 
> CXXFLAGS      = $(CFLAGS) 
> FFLAGS                = -O -xtarget=native -xarch=v9 
> CC_MAKEDEPEND = cc -xM
> COMPILE.c     = $(CC) -c $(CFLAGS) $(CPPFLAGS)
> COMPILE.cxx   = $(CXX) -c $(CXXFLAGS) $(CXXCPPFLAGS)
> COMPILE.f     = $(FC) -c $(FFLAGS)
> # The following command isn't available on some systems; therefore, the
> # `.F.o' rule is relatively complicated.
> COMPILE.F     = $(COMPILE.f) $(FPPFLAGS)
> 
> 
> The files make.log and test.log are attached and a sample of the output
> when testing is given here.
> 
> 
> *** Testing nc_put_varm_schar ...  269 good comparisons. ok
> *** Testing nc_put_varm_short ...  682 good comparisons. ok
> *** Testing nc_put_varm_int ...  1189 good comparisons. ok
> *** Testing nc_put_varm_long ... 
>         FAILURE at line 6471 of test_put.c: range error: status = 0
>         FAILURE at line 6471 of test_put.c: range error: status = 0
>         FAILURE at line 6471 of test_put.c: range error: status = 0
>         FAILURE at line 614 of test_put.c: Var value read not that expected
>         FAILURE at line 614 of test_put.c: Var value read not that expected
>         FAILURE at line 614 of test_put.c: Var value read not that expected
>         FAILURE at line 614 of test_put.c: Var value read not that expected
>         FAILURE at line 614 of test_put.c: Var value read not that expected

Please try the following:

    1.  Put the file "macros.make" back the way it was.

    2.  Perform steps 2 through 4 near the end of the INSTALL file.

    3.  Set the following environment variables to the indicated values:

            CC=/opt/SUNWspro/bin/cc
            CPPFLAGS=
            CFLAGS='-g -xtarget=native -xarch=v9'
            FC=/opt/SUNWspro/bin/f90
            FFLAGS="-g -w -xtarget=native -xarch=v9"
            CXX=/opt/SUNWspro/bin/CC

        You may use an optimization option in place of the "-g" above.
        If you do, then you should also set CPPFLAGS to "-DNDEBUG".

    4.  Ensure that the environment variables FPP and COMPILE_F are
        undefined.

    5.  Perform steps 6 through 9 near the end of the INSTALL file.
        Don't worry about failures in the nf_test/ subdirectory.  They
        merely indicate a problem with the testing code.

Please let me know if this helps.

--------
Steve Emmerson   <http://www.unidata.ucar.edu>