[
Date Prev][
Date Next][
Thread Prev][
Thread Next][
Date Index][
Thread Index]
Re: NEC SX-4 64 bit IEEE Netcdf
- Subject: Re: NEC SX-4 64 bit IEEE Netcdf
- Date: Thu, 27 Nov 1997 21:36:52 +1100 (EST)
Glenn,
On Wed, 26 Nov 1997, Glenn P. Davis wrote:
> > So now 'make' seems to work ok. Then 'make test' runs two C tests ok, but
> > then fails as follows in directory src/fortran:
> >
> > f77 -o ftest -float0 -ew ftest.o ../libsrc/libnetcdf.a
> > undefined first referenced
> > symbol in file
> > nf_get_varm_int2_ ftest.o
> > nf_get_varm_int1_ ftest.o
> > nf_get_vars_int2_ ftest.o
> > nf_get_vars_int1_ ftest.o
> > nf_get_vara_int2_ ftest.o
> > nf_get_vara_int1_ ftest.o
> > nf_get_var1_int2_ ftest.o
> > nf_get_var1_int1_ ftest.o
> > nf_get_var_int2_ ftest.o
> > nf_get_var_int1_ ftest.o
> > nf_get_att_int2_ ftest.o
> > nf_get_att_int1_ ftest.o
> > nf_put_varm_int2_ ftest.o
> > nf_put_varm_int1_ ftest.o
> > nf_put_vars_int2_ ftest.o
> > nf_put_vars_int1_ ftest.o
> > nf_put_vara_int2_ ftest.o
> > nf_put_vara_int1_ ftest.o
> > nf_put_var1_int2_ ftest.o
> > nf_put_var1_int1_ ftest.o
> > nf_put_var_int2_ ftest.o
> > nf_put_var_int1_ ftest.o
> > nf_put_att_int2_ ftest.o
> > nf_put_att_int1_ ftest.o
> > ld fatal: symbol referencing errors. no output written to file ftest.
> > f77 fatal : ld command error : 13
> >
> > I suspect these entry points are not needed, but they cause linkinf to fail.
>
> ftest tests the version 2 compatibility interface (fort-v2compat.c).
> I haven't seen this problem. I used FC=f90, not f77.
I tried FC=f90, which did solve above problem linking ftest in src/fortran.
However ftest produced following:
./ftest
*** Testing nccre ...
*** Testing ncddef ...
*** Testing ncvdef ...
*** Testing ncapt, ncaptc ...
*** Testing ncclos ...
*** Testing ncvpt1 ...
*** Testing ncvgt1 ...
error in ncvgt1 byte: 0 .ne. 122
error in ncvgt1 short: 0 .ne. 10
error in ncvgt1 long: 0 .ne. 1000
error in ncvgt 1 float: 0.000000000000000E+00 not close to
3.141590000000000
error in ncvgt1 double: 0.000000000000000E+00 not close to
0.3333333333000000
error in ncvg1c
*** Testing ncvpt ...
*** Testing ncopn, ncinq, ncdinq, ncvinq, ncanam, ncainq ...
error in ncinq or ncddef
error in ncinq or ncvdef
error in ncinq or ncapt
error: bad recdim from ncinq
*** Testing ncvgt, ncvgtc ...
*** Testing ncagt, ncagtc ...
*** Testing ncredf, ncdren, ncvren, ncaren, ncendf ...
error in ncinq or ncddef
error in ncinq or ncvdef
error in ncinq or ncapt
error: bad recdim from ncinq
*** Testing ncacpy ...
*** Testing ncadel ...
*** Testing fill values ...
error in byte fill value
error in double fill value
error in float fill value
error in long fill value
error in short fill value
> Is it possible that ftest.o or fort-v2compat.o were left over from a
> previous build attempt?
No.
> Does 'make test' in nf_test/ fail as well?
Yes. In fact even using f90, linking still fails for nf_test in similar way
to that in which ftest link failed before. The output is:
undefined first referenced
symbol in file
nf_get_var1_int1_ test_get.o
nf_get_var1_int2_ test_get.o
nf_get_var_int1_ test_get.o
nf_get_var_int2_ test_get.o
nf_get_vara_int1_ test_get.o
nf_get_vara_int2_ test_get.o
nf_get_vars_int1_ test_get.o
nf_get_vars_int2_ test_get.o
nf_get_varm_int1_ test_get.o
nf_get_varm_int2_ test_get.o
nf_get_att_int1_ test_get.o
nf_get_att_int2_ test_get.o
nf_put_var1_int1_ test_put.o
nf_put_var1_int2_ test_put.o
nf_put_var_int1_ test_put.o
nf_put_var_int2_ test_put.o
nf_put_vara_int1_ test_put.o
nf_put_vara_int2_ test_put.o
nf_put_vars_int1_ test_put.o
nf_put_vars_int2_ test_put.o
nf_put_varm_int1_ test_put.o
nf_put_varm_int2_ test_put.o
nf_put_att_int1_ test_put.o
nf_put_att_int2_ test_put.o
ld fatal: symbol referencing errors. no output written to file nf_test.
f90 fatal : ld command error : 13
Thanks again for your help. We seem to be making some progress, even
if rather slowly!
Harvey
Harvey Davies, CSIRO Mathematical and Information Sciences,
Email: address@hidden
Phone: +61 3 9669 8110 or +61 3 9239 4556
Fax: +61 3 9669 8112
